Don't be that guy - DSMCentral

Welcome Guest ( Log In | Register )

Don't be that guy, 13.3 on a fp3065

xian 1g View Member Profile	Jan 28 2005, 03:10 PM Post #1
Eats and sleeps DSM jargin. Group: Members Posts: 1,035 Joined: 31-March 04 From: Chambana Member No.: 268	I was surf'n tuners today.... found a shamefull thread. I'm sure you old timers have seen plenty of these. QUOTE First time down with 3065 -------------------------------------------------------------------------------- I made two passes tonight. The first pass was a 13.6 at 97 missing 4th gear. The second was a 13.3 at 109 with a 2.3 60'. The car bogs bad out the hole but I am on the 3-bolt rear and stock center diff so I am afraid to launch it. Holding the rpm's at 5k and slipping the clutch resulted in this 2.3 60'. When I got back from the track I hooked up the clutch wire and want to go back to the track tomorrow with the stutterbox and no lift to shift to see if that helps with the lag. Leaving the track I beat an LS1 from a 3rd gear roll, the LS1 had just ran a couple 112mph passes. Im currently on 22psi and pump gas with a 20min tune on the car. I have the eprom for 850's, MAF translator set to stock and AFC set to -10 across the board on the high setting. The car gets 2-3 counts of knock in the upper rpm's and gets 18 degrees advance. The car weighs 2,950 and I am about 150lbs. Keep in mind I'm still on a stock downpipe and stock cams. RNR 3'' exhaust is in the mail and I am looking for a set of 272's. ENGINE: stock throttlebody magnus intake ported head with 5angle valve job crower valvesprings arp head studs cometic gasket wiseco 8.5-1 86mm pistons eagle rods align honed bored 1mmover arp rod bolts arp main studs FUEL: walbro 255hp aem rail spoolin afpr FIC 850cc injectors ELECTRONICS/GAUGES: SAFC MAF translator AEM wideband 02 Boost gauge palmV w/ pocketlogger Keydiver chip w/ stage3 mods INDUCTION: 4'' K&N Forced performance cast intake pipe FP3065 28''x10''x3'' front mount w/ 2.5'' piping EXHAUST: ported 2g exhaust manifold 2.5'' 02housing tial 40mm dumped to atm. DRIVETRAIN: ACT 2600 clutch kit Fidanza flywheel he ends up getting flames from the spawn of satan.... eh, the old rule of thumb, fast parts don't make cars fast. -------------------- game over.

Replies (1 - 4)

akamiami View Member Profile	Jan 28 2005, 03:24 PM Post #2
Eats and sleeps DSM jargin. Group: Moderators Posts: 1,156 Joined: 23-September 02 Member No.: 16	don't be that guy that wears a t-shirt of the band at the band's concert. lame also. -------------------- my cars breath smells like car food

haunter

Jan 28 2005, 04:15 PM

Post #3

DSMCentral Freak

Group: Members
Posts: 400
Joined: 6-November 04
From: Urbana
Member No.: 382

afraid of being that guy C?

--------------------

QUOTE (scrapin_frame)

christian, i may be interested in your bottom end!

xian 1g View Member Profile	Jan 28 2005, 04:47 PM Post #4
Eats and sleeps DSM jargin. Group: Members Posts: 1,035 Joined: 31-March 04 From: Chambana Member No.: 268	lol... no... i have good advice I am taking... "nice turbo, don't post anything till it has atleast hit 11's, maybe lower." first couple of runs, yeah, they'll be 13's, in the dark secret track of champaign. that no one sees. time, patience, tuning, goals will be met.. you'll hear then. besides, doug, even if I am that guy, I think that still beats the shaturn -------------------- game over.