 Some ideas needed |
  Jan 30 2005, 11:04 PM
Post
#1
|
|
 DSMCentral Freak  Group: Members Posts: 388 Joined: 2-January 03 From: Peoria Heights Member No.: 59  |
I've got an ACT 2600 installed that’s been in for about 6 or 7 months. Also installed at the same time was an ACT flywheel, and TSS clutch fork. Tranny is a jdm i picked up around the same time, lines and slave cyl are all fairly new. Never had any problem with it until tonight. I left earlier tonight and noticed the clutch felt a little stiff. As I was driving it was taking longer to come off of the floor than usual. By the time I got home when I push the pedal in it is very stiff and stays at floor unless I pull it back up. Any idea what might be the deal? Also a new mitsu TOB was installed as well.
|
 |
 
|
 |
Replies
|
Jan 31 2005, 08:05 AM
Post
#2
|
|
 Zen Master DSM Group: Moderators Posts: 3,008 Joined: 10-January 01 From: in front of you Member No.: 5 |
Haha! Try doing it with a rollcage bar welded into the foot well.
|
|
|
|
Posts in this topic
Taxiwardance Some ideas needed Jan 30 2005, 11:04 PM
MidwestDSM clutch sticking to the floor usually means you are... Jan 30 2005, 11:47 PM haunter damnit nick thats what I was typing........ Jan 30 2005, 11:48 PM MidwestDSM QUOTE (haunter @ Jan 30 2005, 11:48 PM)damnit... Jan 30 2005, 11:51 PM Taxiwardance Fluid level is fine. Was maybe a mm under the full... Jan 31 2005, 12:04 AM Taxiwardance What are the odds of it being the pressure plate? ... Jan 31 2005, 12:06 AM xian 1g are you using an extended slave cylinder rod? Jan 31 2005, 12:18 AM Taxiwardance QUOTE are you using an extended slave cylinder rod... Jan 31 2005, 12:29 AM xian 1g act's, especially 2600's tend to eat them ... Jan 31 2005, 12:31 AM Taxiwardance lmao, I have noticed that its been harder to get i... Jan 31 2005, 12:38 AM Taxiwardance Not sure on the TOB. I'm hoping its something ... Jan 31 2005, 12:49 AM Taxiwardance Well it's not a problem with anything in the t... Jan 31 2005, 01:18 AM Taxiwardance New development. Nevermind on the bleeding the sys... Jan 31 2005, 01:44 AM Taxiwardance I'm almost sure its the master cylinder. I wen... Jan 31 2005, 03:34 AM MidwestDSM nope, not really. a good tactic i've always us... Jan 31 2005, 01:45 PM Taxiwardance Ok need a few more suggestions. I changed the mast... Jan 31 2005, 03:37 PM Taxiwardance And god help me if I have to pull that master cyli... Jan 31 2005, 03:43 PM MidwestDSM sounds like maybe you need to adjust your clutch o... Jan 31 2005, 04:01 PM turbohcar Try this. It may help, it may not. Just a though... Jan 31 2005, 06:04 PM Taxiwardance Thanks for the link. Man that was a lot of fun get... Feb 1 2005, 10:17 PM
turbohcar No problem Taxi. That's what we're all he... Feb 2 2005, 08:12 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 26th September 2026 - 03:15 AM |
Powered By IP.Board
© 2026 IPS, Inc.