Jun 15 2006, 03:23 PM
Post
#1
|
|
|
Eats and sleeps DSM jargin. ![]() ![]() ![]() ![]() ![]() ![]() Group: Moderators Posts: 1,156 Joined: 23-September 02 Member No.: 16 |
Considering how much activity there is on the board, I thought I'd initiate a topic for discussion.
I received the new issues of Modified Mag and SCC in the mail recently and, for a change, each had at least one article worth reading. The Modified Mag had a short story about an R34 Skyline prepared by Midori. The SCC article was a feature story about a chassis builder in Japan known as Opera Performance. Each featured cars with unbelievable attention to detail, expert craftsmanship, and cars with relatively minimal 'typical' modifications that ended up being ruthlessly impressive in the end. I'm not going to repeat a lot of the information, you'll have to read the articles for yourself, and if you don't, your loss. Bottom line is that when I read the articles, I was very impressed by the skill of the shops and builders, as this was about two relatively small shops in Japan which have built world class machines. So far as I know, for all the time and attention US import tuners have put into their vehicles, we're not even close. Our premeir shops are just now starting to put together time attack cars, and in my opinion, they're pretty shitty examples of American half-assed-ness. Even their drag cars, the cars they're most proud of, have obvious room for improvement. Could I do better? No, but I'm not doing this for a business, and as such, not held to such a level of scrutiny. Call it JDM fan-boy bandwagoning if you want, or just being over-critical of others work, in the form of nitpicking US shop cars, but I think that the shops in the US need to get a kick in the nuts. When a car that could very well be driven on the street comes within .4 seconds of breaking the fastest lap time of the JGTC300 record holder at Fuji International, who gives a flying f-bomb if the AMS Evo put down 988 whp. I could give a damn, because shaving nearly 1/3 off the weight of a S2000 is immensely more impressive. -------------------- my cars breath smells like car food
|
|
|
|
![]() |
Jun 16 2006, 09:45 AM
Post
#2
|
|
|
Eats and sleeps DSM jargin. ![]() ![]() ![]() ![]() ![]() ![]() Group: Moderators Posts: 1,156 Joined: 23-September 02 Member No.: 16 |
spyder, I know what you mean about the magazines disappointing, particularly with the project cars. In many ways, I think they're similar to the average enthusiast, but with a bigger budget. They pick up a car, with high hopes and lofty aspirations, install some early mods, but rarely complete the project.
If you're looking for an example of one that was completed, and done quite well, I'd look up the 10 stage RX7 buildup in SCC's archives. It is available on their website, along with the buildup stages of several other cars. Good reads. I'm not expecting the shops in the US to use wiggins clamps on every connection, or exclusively fabricate their intercooler pipes, intakes, and exhausts out of section welded inconel. But that is the type of thing that pushes the market into new areas and more importantly, makes the previously high dollar parts like twin disk carbon clutches more affordable for the average enthusiast. Neither of the cars featured, really had all that much done to the engines, considering the showcase quality of the chassis fabrication was so notable. Here's an idea: If one US shop invested in carbon fiber production capabilities rather than a dyno, they could produce innovative carbon fiber products and secure a definate competetive advantage over the other shops. This would differentiate them from the slew of shops that strictly focus on one aspect of performance (hp vs weight argument, yada yada) and make these 'exotic' parts more readily available to us, the consumers. -------------------- my cars breath smells like car food
|
|
|
|
akamiami The right way to build a car Jun 15 2006, 03:23 PM
99Spyder I myself just left the throne where I was reading/... Jun 15 2006, 06:51 PM
scrapin_frame QUOTE (akamiami @ Jun 15 2006, 03:23 PM)Consi... Jun 15 2006, 07:07 PM
akamiami Link to the SCC project cars Jun 16 2006, 10:08 AM
Itz Darave http://www.diemanmotorsports.com 45 minz from me.... Jun 16 2006, 02:12 PM
akamiami Where is that? I'm not sure where you're ... Jun 16 2006, 03:54 PM
Itz Darave Dieman Motorsports is located in Lee Summit, Misso... Jun 16 2006, 06:57 PM
akamiami Based purely on the article I read in SCC about th... Jun 18 2006, 03:50 AM![]() ![]() |
| Lo-Fi Version | Time is now: 18th November 2026 - 09:46 AM |