Nov 27 2003, 11:58 PM
Post
#1
|
|
|
HONDA KILLER ![]() Group: Members Posts: 7 Joined: 27-November 03 Member No.: 207 |
I recently aquired a 1 gen turbo it doesnt run. im not to sure if its eletrical or engine problem im not familiar with DSM's i used to have a honda but made the switch over.. heres what i have so far spark pluge wire number one is burned off from the spark plug end. Nat was dead when i attached new one i heard noise inside the back panel behind the driver twords the floor. Also under the hood i heard a cicking electrical noise in between the bat and the air intake. other than that i am looking for any info thanks
|
|
|
|
![]() |
Nov 28 2003, 10:26 AM
Post
#2
|
|
|
DSMCentral Godfather ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Group: Admin Posts: 3,823 Joined: 10-January 01 From: Washburn Member No.: 26 |
I hate to jump to conclusions but the clicking on the inside under the dash and clicking in the engine bay lead me to think your ECU is probably toasted. You can check this pretty easily by pulling the ECU out from behinf the center console near the inside firewall. When you open the gold box you will probably find a few capacitors have leaked acid on the board and shorted it out. If this is the case there will also be a smell similar to rotten fish from the acid too.
BTW-I would say the spark plug wire being burned off is probably not related unless the ECU has a lot more power than I think it does. Good luck! -------------------- In Loving memory of David T Crebo
Greatness comes from the most unexpected places! ![]() |
|
|
|
My1Gneeds help 1 gen need help Nov 27 2003, 11:58 PM
My1Gneeds help no it doesnt turn over power to accesories only wo... Nov 29 2003, 12:02 AM
My1Gneeds help It now turns over but doesnt start Nov 29 2003, 08:54 PM
Larz Sounds like the previous owner didn't take car... Nov 29 2003, 10:28 PM
KOU In3 I'd go with Spy's compression check first ... Dec 1 2003, 02:38 PM
My1Gneeds help New brake through it runs on pure starting fluid i... Dec 11 2003, 09:21 PM
natedogg QUOTE (My1Gneeds help @ Dec 11 2003, 09:21 PM... Dec 12 2003, 01:57 PM
KOU In3 Sorry for the off topic but I've been wonderin... Dec 12 2003, 02:42 PM
natedogg Logger says.......cam angle sensor. Switched to a... Dec 12 2003, 02:49 PM
My1Gneeds help i was thinking the same nate dog where is mpi rela... Dec 13 2003, 08:55 PM
natedogg I'm a little fuzzy on relay locations but I be... Dec 14 2003, 10:35 AM
My1Gneeds help now im startin to think fuel pumps bad any one had... Dec 15 2003, 07:19 PM
KOU In3 I've got a spare stocker you can try if you wa... Dec 16 2003, 12:01 AM
ICGerms no, I believe the MPI relay is near the radio...th... Dec 18 2003, 06:33 PM
natedogg There is a relay in the place where I'm talkin... Dec 19 2003, 09:24 AM
My1Gneeds help FUel pump pumps if you atach postive lead to the c... Dec 21 2003, 12:02 AM![]() ![]() |
| Lo-Fi Version | Time is now: 25th September 2026 - 09:53 AM |