 SAFC-2 or GM MAS |
  |
 Apr 30 2004, 07:00 PM
Post
#1
|
|
 DSMCentral Freak  Group: Members Posts: 388 Joined: 2-January 03 From: Peoria Heights Member No.: 59  |
What should i go with? Im not making a shit load of power right now but im running a 16g, with 95 pistons, 190 rewired fuel pump, exhaust and supra intercooler in the mail, and a bunch of other shit i cant think of. Whats the better set up?
|
 |
 
|
|
Apr 30 2004, 07:40 PM
Post
#2
|
|
 Post Master Group: Members Posts: 774 Joined: 28-October 02 From: Pekin Member No.: 32 |
New version Translator. My understanding is that the originals were very easy to work with, but lacked in the fine tuning arena, but they are much improved with Ver 2.0, and still easier to operate than the S-AFC. Also, if you pick a sensor out of a yard, it could be about $100 cheaper. My .02.
-------------------- 2009 Scion Tc
1994 Del Sol Si 1991 Talon TSi AWD 1990 Mustang GT FOR SALE!!! |
|
|
|
|
May 1 2004, 01:00 PM
Post
#3
|
|
 Person of Wisdom Group: Members Posts: 142 Joined: 14-March 04 From: peoria Member No.: 258 |
i've got both, on my car, and still tryin to figure out what to go with...
-------------------- Stupid White Kid Racing
Run your car, not your mouth.... |
|
|
|
|
May 2 2004, 12:38 AM
Post
#4
|
|
|
DSMCentral Freak Group: Members Posts: 388 Joined: 2-January 03 From: Peoria Heights Member No.: 59 |
Well damn, now im more confused than i was before i posted the question. I think im going to go with the GM MAS. I found a setup from green performance for a 3inch 2.08 setup shipped for 280$. But damn, I can get a safc2 for 280$ also.
 Hmmm looks like i might have to do a coin toss to decide here.
|
|
|
|
|
May 2 2004, 12:43 AM
Post
#5
|
|
 Post Master Group: Members Posts: 972 Joined: 30-October 02 Member No.: 34 |
Go with the MAFt translator. Easier to tune, less intake restriction, etc. If you buy the SAFC you'll need a 2G mas relatively soon as well.
But you might want to source your own 3" GM MAS. From what I hear they can be had a lot cheaper than $80. Of course I'm still looking for a couple so that doesn't mean much. I am however running a MAS translator on all the cars here (2 up and running and one installed on a project car), so yopu can see where I'd lean there if I were you. -------------------- |
|
|
|
|
May 2 2004, 07:21 AM
Post
#6
|
|
|
DSMCentral Freak Group: Members Posts: 388 Joined: 2-January 03 From: Peoria Heights Member No.: 59 |
Heads it is! Thanks for the info, i'm going to do some searching and see what i can find a gm mas for.
|
|
|
|
|
May 2 2004, 07:46 AM
Post
#7
|
|
 Post Master Group: Members Posts: 908 Joined: 7-October 03 From: Chillicothe, IL Member No.: 182 |
blow through or draw through? I have a 4" if you want to go draw through. 10$ and its yours.
-------------------- GVR4 866/1000 = the perpetually broken car
|
|
|
|
|
May 2 2004, 09:32 AM
Post
#8
|
|
 Post Master Group: Members Posts: 658 Joined: 7-October 03 From: Pekin Member No.: 181 |
|
|
|
|
|
May 2 2004, 12:05 PM
Post
#9
|
|
 Zen Master DSM Group: Moderators Posts: 3,008 Joined: 10-January 01 From: in front of you Member No.: 5 |
QUOTE (ncgalant @ May 2 2004, 07:46 AM) blow through or draw through? I have a 4" if you want to go draw through. 10$ and its yours. A 4"! Geez, what did that come off of, a diesel? I don't think the MAFT even calibrates for a 4" MAF. Last I checked there is calibration for a 3", 3.5", or the Z06 3.625". I have had an easy time tuning my car in with the 3.5" MAF in drawthrough. Its pretty user friendly and doesn't seem as finicky as the SAFC was when I had that installed on my old fwd. I haven't installed my version 2.0 chip yet which allows for the finer tuning. I probably won't until I get some good strip runs in on my current tune with the older chip. |
|
|
|
|
May 2 2004, 12:38 PM
Post
#10
|
|
|
DSMCentral Freak Group: Members Posts: 388 Joined: 2-January 03 From: Peoria Heights Member No.: 59 |
Cool, thanks for all the info. What's the diffrence between a drawthrough and blowthough setup?
|
|
|
|
|
May 2 2004, 01:15 PM
Post
#11
|
|
|
Post Master Group: Members Posts: 774 Joined: 28-October 02 From: Pekin Member No.: 32 |
Draw through is before the air enters the turbo i.e., factory set-up. Blow through is after the turbo, usually on the uicp, after the bov, between bov and the t/b. Allows bov to be vented to atmosphere w/out momentary rich condition or stalling, etc.
-------------------- 2009 Scion Tc
1994 Del Sol Si 1991 Talon TSi AWD 1990 Mustang GT FOR SALE!!! |
|
|
|
|
May 2 2004, 01:44 PM
Post
#12
|
|
|
Post Master Group: Members Posts: 908 Joined: 7-October 03 From: Chillicothe, IL Member No.: 182 |
They sell an adapter to use this MAF. Its from a suburban IIRC. I bought it a long time ago when I thought I was going to be needing it. PM me if intersted.
-------------------- GVR4 866/1000 = the perpetually broken car
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 21st December 2025 - 10:10 PM |
Powered By IP.Board
© 2025 IPS, Inc.