 Tranny Help!!!!, help me |
 Nov 14 2006, 12:13 PM
Post
#1
|
|
 Post Master  Group: Members Posts: 864 Joined: 12-July 05 From: Illinois Member No.: 556  |
Ok guys, I have been dicking with this since I owned the car and need help asap. The following parts have been replaced:
slave cylinder clutch & pressure plate clutch fork pivot ball SS clutch line rebuilt tranny throwout bearing throwout bearing spring Now to the problem, When i first installed the tranny and blead the clutch the car backed out of the garage normal and fine. Today when i tried to go into reverse ( or any gear ) it grinds. I am pretty sure that the clutch fluid system is loosing pressure somehow but not !00% sure. If i try to put it into gear slowly in will not go all the way in and moves forward ( which is the clutch not being engaged all the way, duh! ) I need help ASAP cause its not fun fixing the same thing 20 times. Any help appreciated! thanks Travis -------------------- "One of the most Crazy and Undecisive Members in central Illinois"
|
 |
 
|
 |
Replies
(1 - 11)
|
Nov 14 2006, 12:38 PM
Post
#2
|
|
 Zen Master DSM Group: Moderators Posts: 3,008 Joined: 10-January 01 From: in front of you Member No.: 5 |
Will it shift okay with the engine off? Are you sure you bled all the air out of the hydraulics? If you don't have someone helping you sometimes you can suck air back in through the bleeder valve.
|
|
|
|
|
Nov 14 2006, 12:47 PM
Post
#3
|
|
|
DSM Tech Wizard Group: Members Posts: 2,256 Joined: 10-January 01 From: central IL Member No.: 10 |
assuming the syncros were replaced with the rebuild?
-------------------- The fastest car I own is a minivan....
|
|
|
|
|
Nov 14 2006, 06:30 PM
Post
#4
|
|
|
DSM Tech Wizard Group: Members Posts: 2,404 Joined: 16-December 03 From: Fletcher/Bloomington Member No.: 214 |
And there's always the problem with the clutch pedal bushings under the dash.
Check all of these things and make sure. -------------------- "I hear he tunes the space shuttle also...and that thing is fast"
|
|
|
|
|
Nov 14 2006, 07:58 PM
Post
#5
|
|
 Post Master Group: Members Posts: 780 Joined: 14-July 04 Member No.: 338 |
Also, don't forget that your master cylinder can be a cause of leaks. Once you start strengthening the rest of the system, the weak spots start showing themselves.
-------------------- QUOTE (gsxracer80 @ Oct 31 2006, 12:41 AM)
thanks hcar.... I am still massaging that area trying to get it ready...  |
|
|
|
|
Nov 14 2006, 09:44 PM
Post
#6
|
|
|
Info Seeker Group: Posts: 75 Joined: 24-January 06 Member No.: 786 |
did you put washers behind the pivot ball ? i had to pull my tranny 3 times before i got mine working. how long did it work fine for? mine did exactly what you are saying but it wouldnt go in gear at all.
|
|
|
|
|
Nov 15 2006, 09:01 AM
Post
#7
|
|
|
Post Master Group: Members Posts: 864 Joined: 12-July 05 From: Illinois Member No.: 556 |
Yes I did have help with the bleading and Im 99% sure its blead correctly w/ no air.
The tranny goes into all gears fine with the engine off. I did not put washers behind the pivot ball because I found it not necessary with the brand new clutch fork and pivot ball! Well, Im not 100% on the syncro deal, but if anyone knows what was done to Tommy's tranny , cause thats the one i have now. I bought this one off him. he said they were replaced and that it worked fine for him. I was aiming towards the master cylinder since it held [ressure right after the bleading and then a few days later it was weak again. i havent checked for leaking, where are places to look? Also, have any of you used an autoparts master cylinder? -------------------- "One of the most Crazy and Undecisive Members in central Illinois"
|
|
|
|
|
Nov 15 2006, 09:13 AM
Post
#8
|
|
|
Zen Master DSM Group: Moderators Posts: 3,008 Joined: 10-January 01 From: in front of you Member No.: 5 |
Check the driver foot well or the firewall for fluid. Those are the most common places.
|
|
|
|
|
Nov 16 2006, 11:26 AM
Post
#9
|
|
|
Post Master Group: Members Posts: 780 Joined: 14-July 04 Member No.: 338 |
A washer behind the pivot ball would be beneficial even with new parts. A stronger clutch might just need that extra throw. Shoot, brent needed two washers on his, and it was a stock clutch!
-------------------- QUOTE (gsxracer80 @ Oct 31 2006, 12:41 AM)
thanks hcar.... I am still massaging that area trying to get it ready... |
|
|
|
|
Nov 17 2006, 04:47 AM
Post
#10
|
|
|
Post Master Group: Members Posts: 864 Joined: 12-July 05 From: Illinois Member No.: 556 |
It has a Centerforce clutch in it, so i guess if i come to the conclusion that its not pressure related then I will try the washer thing!
I will keep you guys updated after this weekend! thanks for all the advice -------------------- "One of the most Crazy and Undecisive Members in central Illinois"
|
|
|
|
|
Nov 18 2006, 11:56 PM
Post
#11
|
|
 Info Seeker Group: Members Posts: 52 Joined: 6-July 05 From: Nor Cal Member No.: 552 |
buy a honda and you wont have that problem just messin with you bro you kno how it is
-------------------- Nitrous is like a hooker, you wanna' hit it but you're scared of the consequences
90 Talon TSi |
|
|
|
|
Nov 19 2006, 12:41 PM
Post
#12
|
|
|
Post Master Group: Members Posts: 864 Joined: 12-July 05 From: Illinois Member No.: 556 |
Haha, funny! I think you need to sell yours and buy A DAMN DSM.
I know! -------------------- "One of the most Crazy and Undecisive Members in central Illinois"
|
|
|
|
 |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 10th October 2025 - 05:05 AM |
Powered By IP.Board
© 2025 IPS, Inc.