 Transfer case, help! |
  |
  Aug 14 2003, 05:07 PM
Post
#1
|
|
 DSMCentral Freak  Group: Members Posts: 388 Joined: 2-January 03 From: Peoria Heights Member No.: 59  |
Well ive got everything disconnected and the engine ready to pull exept i cant get the transfer case off???? The manual says, drain-remove 4 bolts (there was 5 on mine?) then pull to the side and remove of driveshaft. I have the bolts off but i cant disengage it from the tranny/driveshaft someone tell me what im doing wrong.
|
 |
 
|
|
Aug 14 2003, 05:45 PM
Post
#2
|
|
 Post Master Group: Members Posts: 626 Joined: 25-September 02 From: Urbana, IL Member No.: 19 |
It should come off, assuming you removed the correct bolts (5 - 17mm head). If it has never been off before, its likely quite stuck, and you'll have to pry it away from the transmission. You'll want to grease the splines a little before you re-assemble it.
-------------------- Eric Wort
87 White Buick Turbo 'T' (11.71 @ 116.5, 1.61 60ft, slipping trans) 92 Teal Eagle Talon TSi AWD (burn victim) |
|
|
|
|
Aug 14 2003, 07:49 PM
Post
#3
|
|
|
DSMCentral Freak Group: Members Posts: 388 Joined: 2-January 03 From: Peoria Heights Member No.: 59 |
Yep i got all 5 17mm bolts, i just had the tranny rebuilt at joshes a few weeks ago and he cleaned everything up so i would assume it should just come off?? Ille go take anither try. thanks
|
|
|
|
|
Aug 14 2003, 07:57 PM
Post
#4
|
|
|
DSMCentral Freak Group: Members Posts: 436 Joined: 21-September 02 From: Urbana Member No.: 15 |
Get a lot of flat head screw drivers and start pounding those bitches in like wedges until the slut pops off!
-------------------- |
|
|
|
|
Aug 15 2003, 02:13 AM
Post
#5
|
|
|
DSMCentral Freak Group: Members Posts: 388 Joined: 2-January 03 From: Peoria Heights Member No.: 59 |
Engines out!!!!! and its only 3 AM, the neighbors probably don’t like me anymore though
 Transfer case came off after a little persuasion. my main problem ended up being the control arms (needed to come off because of bad ball joints) I am now looking for a set of used ones with good joints and I also need a set of ball joint type links that connect the sway bar to the control arm. They were both completely rounded out so I just cut them in half on the shaft. If anyone has a parts car with a good set let me know ASAP. Thanks for all the help.
|
|
|
|
|
Aug 15 2003, 07:38 AM
Post
#6
|
|
|
DSMCentral Godfather Group: Admin Posts: 3,823 Joined: 10-January 01 From: Washburn Member No.: 26 |
You can pick up new stock sway bar end links at a very reasonable price as long as you don't go to a dealer. BTW - let us know what you find inside.
-------------------- In Loving memory of David T Crebo
Greatness comes from the most unexpected places!  |
|
|
|
|
Aug 15 2003, 07:58 AM
Post
#7
|
|
|
DSMCentral Freak Group: Members Posts: 388 Joined: 2-January 03 From: Peoria Heights Member No.: 59 |
yep it was a bearing. It was my front balance shaft bearing the one right next to the case. Thats all ive noticed so far i'm waiting for autozone to open for a few parts then im going to drop the crank later. everything seems solid in there though. Also my oil pump pick up tube was probably 30% blocked from bearing shavings. When i pulled the balance shaft the bearing came out with it, just kind of sitting on it. Now im going to have to fork over shit loads of cash to Kalinas to get all of my machine work done.
|
|
|
|
|
Aug 15 2003, 09:02 AM
Post
#8
|
|
|
DSM Tech Wizard Group: Members Posts: 2,256 Joined: 10-January 01 From: central IL Member No.: 10 |
If it's just a balance shaft, you might be able to get by with just putting an eliminator kit in and buttoning it back up. There is always the possiblility that the shavings got into other stuff and caused damage. I guess it comes down to asking yourself if you feel lucky....
well, do ya.... punk... 
-------------------- The fastest car I own is a minivan....
|
|
|
|
|
Aug 15 2003, 11:51 AM
Post
#9
|
|
 Post Master Group: Members Posts: 729 Joined: 19-September 02 From: New Baden, IL Member No.: 7 |
QUOTE (POS AWD @ Aug 15 2003, 09:02 AM) I guess it comes down to asking yourself if you feel lucky.... well, do ya.... punk...  HA HA HA! YOU SO FUNNY!!
-------------------- -The original (member) 007. Stop looking at me Spy!!
-98 S-10 P/U creepin' low on stock 15s!! -You come off just a little more intelligent if you know how to spell the insults in addition to saying them |
|
|
|
|
Aug 15 2003, 01:56 PM
Post
#10
|
|
 Post Master Group: Members Posts: 972 Joined: 30-October 02 Member No.: 34 |
QUOTE (Taxiwardance @ Aug 15 2003, 08:13 AM) Engines out!!!!! and its only 3 AM, the neighbors probably don’t like me anymore though Transfer case came off after a little persuasion. my main problem ended up being the control arms (needed to come off because of bad ball joints) I am now looking for a set of used ones with good joints and I also need a set of ball joint type links that connect the sway bar to the control arm. They were both completely rounded out so I just cut them in half on the shaft. If anyone has a parts car with a good set let me know ASAP. Thanks for all the help.I've got most of those parts if they're for a 1G AWD. Might be a few days before they are off the car and available though so not sure how much help I can be if you are on a short timeline. Sent you a PM -------------------- |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 16th June 2026 - 10:00 PM |
Powered By IP.Board
© 2026 IPS, Inc.