Welcome Guest ( Log In | Register )

5 Pages V  < 1 2 3 4 5 >  
Reply to this topicStart new topic
> Project Black Golfball-plans for 2010
black92_tsi_awd
post May 25 2010, 08:28 PM
Post #41


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



Well maybe...

Pass side axle started leaking Sunday. Swapped in another new seal, old one seemed to have a small knick in it. However the new seal is leaking.

After some taling to Darryl...and some internet searching by him. We came up with a thread on DSMTalk where a guy got a bad axle that wouldn't stop leaking. He replaced the seal 3 time and it wouldn't stop leaking, swapped in another axle and it was fine. Off to Advance again and see if they'll give me another to try.

Anybody else had a similiar experience?/


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
dualdj1
post May 26 2010, 07:58 AM
Post #42


DSMCentral Freak
****

Group: Admin
Posts: 490
Joined: 15-September 08
From: East Peoria, IL
Member No.: 8,716



QUOTE (black92_tsi_awd @ May 25 2010, 09:28 PM) *
Well maybe...

Pass side axle started leaking Sunday. Swapped in another new seal, old one seemed to have a small knick in it. However the new seal is leaking.

After some taling to Darryl...and some internet searching by him. We came up with a thread on DSMTalk where a guy got a bad axle that wouldn't stop leaking. He replaced the seal 3 time and it wouldn't stop leaking, swapped in another axle and it was fine. Off to Advance again and see if they'll give me another to try.

Anybody else had a similiar experience?/


haven't, but could easily see that happening. Take a Micrometer with you if you have one, and mic out both axles where the seal sits to see if there's a difference. Also can make sure it's perfectly round that way.


--------------------
1978 Mustang II King Cobra
89 5.0HO, Stock Short Block, Ford F303 cam, 1.7:1 Crane Roller Rockers, Holley 650 Doubler Pumper, MSD 6AL, Pocket Ported stock heads, Hedman Long Tube Headers
5 spd Manual
Full roll cage, 9" full floater w/Currie trac lock/373 gears, RCI Fuel Cell
Project Page: http://www.brandttuning.com/projects.htm
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post May 26 2010, 09:19 PM
Post #43


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



Looks like I solved the problem (finger crossed).

The axle that was in there had a sealing surface of 1.614" in dia. The axle I picked up today has a dia of 1.378"!! The bigger axle had pushed the seal into the case when I tapped it in to get the c-clip to seat. I should have known better.

So I got the round friggin axle from Advance! They said they would swap it no charge but what a pain in the a$$.

Drove my daughter to softball tonight and no leaks.


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
dualdj1
post May 27 2010, 07:20 AM
Post #44


DSMCentral Freak
****

Group: Admin
Posts: 490
Joined: 15-September 08
From: East Peoria, IL
Member No.: 8,716



sweet, glad to hear it's finally coming together!


--------------------
1978 Mustang II King Cobra
89 5.0HO, Stock Short Block, Ford F303 cam, 1.7:1 Crane Roller Rockers, Holley 650 Doubler Pumper, MSD 6AL, Pocket Ported stock heads, Hedman Long Tube Headers
5 spd Manual
Full roll cage, 9" full floater w/Currie trac lock/373 gears, RCI Fuel Cell
Project Page: http://www.brandttuning.com/projects.htm
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post May 27 2010, 07:34 PM
Post #45


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



and she's down again.

something in the trans or clutch is rattling.

back on the jack stands it goes.


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Jul 11 2010, 01:31 PM
Post #46


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



Got the gears sets rebuilted after eating a couple of gears. I can't get a bearing race out of the trans for the input shaft so I said screw it and assembled the old stock trans with upgraded shift forks I bought from Darryl.

Got the old trans installed and at least the cars running right now and maybe I can finish breaking in the new clutch and have some fun with the car.

Took it out today and seems to be running pretty good. Need to find my logger and see how the tune is.

My autometer shift light seems to have taken a dump. Goes off randomly between 3000 and where ever the shift pill is.


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Jul 26 2010, 07:53 PM
Post #47


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



Took the Talon out to check the launch rpm on the stutter with the new clutch/flywheel combo. Left at 5800, spun all four tires and first gear exploded after about 15 feet. By the looks of the tires tracks, the front wheels started hopping and the shock load must have destroyed first. I've got my other trans to put together but it'll be tough to make the CSS Street car challange and defend my belt...8(


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
dualdj1
post Jul 27 2010, 07:55 AM
Post #48


DSMCentral Freak
****

Group: Admin
Posts: 490
Joined: 15-September 08
From: East Peoria, IL
Member No.: 8,716



damn man, You just can't keep that thing together. too much power tongue.gif

tough luck though, hope you can get it fixed


--------------------
1978 Mustang II King Cobra
89 5.0HO, Stock Short Block, Ford F303 cam, 1.7:1 Crane Roller Rockers, Holley 650 Doubler Pumper, MSD 6AL, Pocket Ported stock heads, Hedman Long Tube Headers
5 spd Manual
Full roll cage, 9" full floater w/Currie trac lock/373 gears, RCI Fuel Cell
Project Page: http://www.brandttuning.com/projects.htm
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Aug 24 2010, 07:21 PM
Post #49


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



Well here's a picture of the burnout and a couple of the resulting carnage.

Attached File(s)
Attached File  burnout.jpg ( 73.13K ) Number of downloads: 4
Attached File  trans1.jpg ( 59.27K ) Number of downloads: 4
Attached File  trans2.jpg ( 59.15K ) Number of downloads: 3
 


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Aug 24 2010, 07:25 PM
Post #50


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



I did manage to get it to the CSS Street Car Challange. Alternator bolt sheared of on the drive down. Luckily I carry an extra alternator when I got to the track. Didn't have the correct bolt, but a little redneck engineering got me running again.

Only ran a best of 12.79 but was fighting wheel hop all day and didn't want to blow another trans.
Attached File(s)
Attached File  redneck_engineering.jpg ( 65.81K ) Number of downloads: 3
 


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
dualdj1
post Aug 25 2010, 12:35 PM
Post #51


DSMCentral Freak
****

Group: Admin
Posts: 490
Joined: 15-September 08
From: East Peoria, IL
Member No.: 8,716



lol sooner or later you'll have replaced everything on that car, then maybe it'll hold together for ya

glad to see you at least got some track time though


--------------------
1978 Mustang II King Cobra
89 5.0HO, Stock Short Block, Ford F303 cam, 1.7:1 Crane Roller Rockers, Holley 650 Doubler Pumper, MSD 6AL, Pocket Ported stock heads, Hedman Long Tube Headers
5 spd Manual
Full roll cage, 9" full floater w/Currie trac lock/373 gears, RCI Fuel Cell
Project Page: http://www.brandttuning.com/projects.htm
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Oct 1 2010, 06:26 PM
Post #52


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



The race trans started grinding 4th gear so out it came...

I rebuilt the grenaded trans and swapped it for the race trans today today. Shifts pretty good and should get me back to the track soon.

Guess I'll bust the case open on the race trans and look at 4th gear hub and syncros.


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
awd4kicks
post Oct 1 2010, 11:16 PM
Post #53


DSMCentral Godfather
********

Group: Admin
Posts: 3,823
Joined: 10-January 01
From: Washburn
Member No.: 26



QUOTE (black92_tsi_awd @ Oct 2 2010, 12:26 AM) *
The race trans started grinding 4th gear so out it came...

I rebuilt the grenaded trans and swapped it for the race trans today today. Shifts pretty good and should get me back to the track soon.

Guess I'll bust the case open on the race trans and look at 4th gear hub and syncros.


Keeping the dream alive...


--------------------
In Loving memory of David T Crebo
Greatness comes from the most unexpected places!
user posted image
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Oct 2 2010, 08:12 AM
Post #54


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



QUOTE (awd4kicks @ Oct 2 2010, 12:16 AM) *
Keeping the dream alive...


Or the nightmare! 8)

Looks like I might hit thetrack this Friday.


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Oct 13 2010, 06:36 PM
Post #55


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



Went to the track last Friday, didn't do too bad. My quicky trans rebuild stayed together and shifts pretty well.

12.85 @ 107.0 1.69 60' on 17psi
12.82 @ 109.0 1.82 on 20-21psi
12.769 @ 109.7 1.85
12.604 @109.3 1.72
12.687 @ 109.91 1.77
12.426 @ 110.15 1.675 60'

Still have some wheel hop issues. Probably need to replace the mounts with poly. They are "window welded" but the rubber material is being pushed out of the mount.

I don't know how much faster the 14b will go. Last runs the tune was pretty good, almost no knock, 20-21 degrees timing, WB was 11.2 and boost was spiking to 21 and falliong off at the end of each gear.

Off to V-day Sunday!


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
dualdj1
post Oct 15 2010, 09:02 AM
Post #56


DSMCentral Freak
****

Group: Admin
Posts: 490
Joined: 15-September 08
From: East Peoria, IL
Member No.: 8,716



nice work, looks like a good solid setup.


--------------------
1978 Mustang II King Cobra
89 5.0HO, Stock Short Block, Ford F303 cam, 1.7:1 Crane Roller Rockers, Holley 650 Doubler Pumper, MSD 6AL, Pocket Ported stock heads, Hedman Long Tube Headers
5 spd Manual
Full roll cage, 9" full floater w/Currie trac lock/373 gears, RCI Fuel Cell
Project Page: http://www.brandttuning.com/projects.htm
Go to the top of the page
 
+Quote Post
awd4kicks
post Oct 16 2010, 11:16 AM
Post #57


DSMCentral Godfather
********

Group: Admin
Posts: 3,823
Joined: 10-January 01
From: Washburn
Member No.: 26



Good job Chris!


--------------------
In Loving memory of David T Crebo
Greatness comes from the most unexpected places!
user posted image
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Oct 16 2010, 12:06 PM
Post #58


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



Carrier bearing was getting a little sloppy so I refilled it Friday with silicone like I did 4 years ago.

Problem is I can't get the damn silicone to dry...I keep running a heat gun on it. Should have never did it with racing Sunday.


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
mitsu90
post Oct 16 2010, 01:50 PM
Post #59


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,754
Joined: 25-June 04
From: 61554
Member No.: 314



Stick a heat lamp on it or maybe even a 100 watt bulb might be enough heat.


--------------------
┌∩┐(_)┌∩┐
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Oct 17 2010, 07:00 PM
Post #60


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



I survived Vicary Day!!

Car had wheel hop problems all day.

12.89@107.9 on 17psi
13.67@108.6 major wheel hop, had to get out of the throttle
12.50@109.4
12.62@109.4
12.56@109.2
12.68@108.4

Most of the 60's where in the 1.7x's

Time to get some poly engine mounts and a BIGGER turbo!


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post

5 Pages V  < 1 2 3 4 5 >
Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: 8th October 2025 - 05:02 AM
Design by: IPB Download & eBusiness Discussions