all_wheel_envy
Jul 9 2004, 08:07 PM
i was on vfaq and i cant find how to trick my stock maf by wiring the resistor. does
anyone know how to or where to get the info
turbohcar
Jul 9 2004, 09:24 PM
trick it into doing what?
ranta18
Jul 10 2004, 12:36 PM
Probably by making it think its getting more air that it really is or something completely assinine like that.
all_wheel_envy
Jul 10 2004, 01:45 PM
SO THAT I CAN RUN MORE BOOST
xian 1g
Jul 10 2004, 02:11 PM
are you talking about removing honecombs from the maf so that you can run more boost? adds like 2-3psi.
all_wheel_envy
Jul 10 2004, 04:36 PM
thanks spy
Justincredible
Jul 10 2004, 07:26 PM
QUOTE (ranta18 @ Jul 10 2004, 01:36 PM)
Probably by making it think its getting more air that it really is or something completely assinine like that.
go back to honda's. you dont know nothing about the boost.
turbohcar
Jul 10 2004, 11:10 PM
I'm not sure how exactly you would get more boost just by removing some honeycombs on the MAF?
JMoushon
Jul 11 2004, 08:13 AM
I think there is a bit of confusion. Included in the "free mods" is the removal of the boost restrictor, which does give you a couple xtra psi. Also in the free mods is the removal of the lower honeycombs. They are usually done the day you get the car, but are mutually exclusive mods. They are not related, therefore, to my knowledge, you get no more boost from removing honeycombs. Ask Nate about the blaha mod, he can explain it better than I can.
ranta18
Jul 11 2004, 11:41 AM
QUOTE
go back to honda's. you dont know nothing about the boost.
How fast has your car gone again? What I thought. SHUT IT!
Justincredible
Jul 11 2004, 12:50 PM
QUOTE (ranta18 @ Jul 11 2004, 12:41 PM)
How fast has your car gone again? What I thought. SHUT IT!
I dont know. How the hell would you even know?? Its never been to the track. do you know anything about dsm's and what mods do what?
But I'm DAMN sure for the price of just your god damn MAD TITE JAYDM motor. I have put it into performance mods.
BUT to get on here and trash A FREE mod to modify the performance of somebodies car by calling it assinine is utter and complete BULLSHIT!
THEN TO HAVE A COMEBACK OF HOW FAST HAS YOUR CAR GONE is JUST AS STUPID!! you sound like a fuckin 3rd grade bitch.
ranta18
Jul 11 2004, 03:39 PM
AHAHAHAHA. You make me laugh. Grow up kid. You have no idea do you.
JMoushon
Jul 11 2004, 04:23 PM
See what happens when CII is down? A good thread turned to crap. And for the record, Mike, just to clarify... As Justin's car sits, given one good dyno tuning session, it would go far quicker than 12.8. Marcus ran 12.6 on a 14b, and Justin (for now) is on an Evo 3 16g with plenty of supporting mods. On the street he would give you a solid run. Just my opinion, not trying to stir up more shit. You would still beat me by a long shot...for now.
Justincredible
Jul 11 2004, 04:40 PM
QUOTE (ranta18 @ Jul 11 2004, 04:39 PM)
AHAHAHAHA. You make me laugh. Grow up kid. You have no idea do you.
you know what I got one more thing to say and I'm done cause your defacating on a SWEET board dedicated to dsm's problems and talks only.
if you ask me you need to step off this pedastal you've put yourself on. 12.8 aint that fast. yea its cool you did it and all but you waive it around like your king ding-a-ling. if you wanna put a 100 spot down that says I can't run faster than that come on throw down.
ranta18
Jul 11 2004, 04:52 PM
AHAHAHA. Please stop... my stomach hurts from all this laughing.
For the record I didn't start anything. I just said that those mods where you wire in a resistor to your IAT or MAF sensor is plain dumb. Justignorant took it upon himself to start shit with me and ASSumed I know nothing about modding DSM's. That was his first mistake. I never said anything about my car being fast or that 12.8 was fast. He make a poke at me and Hondas and I made a poke at him how his car isn't fast anyway. One poke deserves another. Don't start shit if you can't take shit.
JMoushon
Jul 11 2004, 06:13 PM
I know, Mike. I wasn't saying you were trying to start an argument. I was just trying to let a bit of reality into the situation. With the exception of Darryl, no one on here, to my knowledge has a track only car. I was more trying to point out the street car vs race car without directly saying it. You ask, what has your car run, and most people on here won't know. But if you ask them, can you beat x car, they'll know. For the record, from what I've read, some people have awesome results from the blaha type mods, and some people claim it ruined their car. I'm not willing to take that chance when viable and predictable management options are available. So in that respect I agree. I think Justin was simply asking why you would bash a free mod. And for the record, although a few may know better, most on this board assume you are a Honda-specific person, with no DSM experience, so expect things like that. I run into the reverse all the time. Just because I run my DSM, most people forget I even own a Honda, let alone know anything about them. In reality, I probably know more about Honda's than I do about DSMs. Who knew?
THIS IS NOT CII. STOP THE INSANITY.
ranta18
Jul 11 2004, 06:52 PM
Its cool Moushon. I stated my opinion on the mod and he came back with a lame attack that I drive a Honda and know nothing about DSM's or boost. It had nothing to do with the original topic. I asked how fast his car was to show he doesn't know everything about boost or DSM's either (if he had a 9 or 10 sec DSM, I'd say he did know a lot). And a side note that there are PLENTY of Hondas that are faster than him, so his comments make no sense at all. I made NO comparison between my car and his, thats just what he assumed. Later on he comes back talking shit about my car, the classic comment, "my car has less in it than yours", and calling me names. How childish is that. He fucked up by assuming I know nothing when I probably know more than he does and I doubt he'll have any sort of appology for me.
I don't mean to start any drama, it was brought apon me. I then feel the need to defend myself. Maybe you should tell others not to assume things about other people.
ranta18
Jul 11 2004, 07:12 PM
Thanks, but I have plenty experience already. If you want to come over this week and watch while I build my buddy's 4G63 engine back up with new pistons, bearings, ... basically everything, feel free. You can also check out the FMIC setup and intake piping I made for it. Its pretty nice.
all_wheel_envy
Jul 11 2004, 07:17 PM
ok since you know every thing are you going to help me or just sit here and bash me all i want to know is how i can do this and the risk i take
xian 1g
Jul 11 2004, 08:37 PM
yeah sorry i missed the obvious title 'blaha'...
side note: interesting to find that the roles have reversed and now justin is post whoring on mr. envy's thread... lol
my worthless .02 anything that can be done free should be done. I'll search the vfags later.
ranta18
Jul 12 2004, 07:37 AM
Oh don't you worry what it will run, just worry about keeping up with it. LOL! I love how you think I know nothing since I mainly work on Hondas. Goes to show how much YOU know and how ignorant you really are. Keep it up, it makes you look real mature. Please explain your reason of thinking and why I CAN'T POSSIBLY know anything about the oh so powerful world of DSM's?
I am victim to the same thing as Xian 1g and missed the blaha. I just read the original post and it sounded like one of those stupid resistors you wire into your IAT or something to fool the computer. The way he worded "trick my stock maf by wiring the resistor" made me think of that. My bad. But, I take it he's running 17 psi or so now. Where does the effeciency of the 14b run out? I thought I remember seeing it didn't really make that much more power at 20 psi because its out of its effeciency range. What is the max rpm for a 14b and how fast will 20 psi spin it? All things to think about. It might make a little more power, but is it worth it by risking the turbo. I'd just get a Walbro 255lph high pressure fuel pump, krissj144 mbc, and chill until you can afford injectors and a bigger turbo. There are other things like full exhaust, FMIC, new intake pipes, etc that you can do too. I know everyone wants that last little bit of extra hp and doesn't want to pay for it, but you might just pay for it and more in then end with a blown turbo.
SCCA Stang
Jul 12 2004, 10:38 AM
QUOTE
Where does the effeciency of the 14b run out? I thought I remember seeing it didn't really make that much more power at 20 psi because its out of its effeciency range. What is the max rpm for a 14b and how fast will 20 psi spin it? All things to think about. It might make a little more power, but is it worth it by risking the turbo.
I am not sure what the eficiency range is... i think that it varies between turbo to turbo.... some 14b's run good at 20+ lbs (mine used to pull like a maniac above 20 lbs) some i've heard don't make good power after 17 lbs
ranta18
Jul 12 2004, 11:02 AM
8"? Thats it? LOL. J/K.
The definition of experience is very vague and you assumed I ment I'm a master mechanic and know all. I admit I am not at all a master and do not know everything, but I do know some things already and thats why I said I have experience. It was just that your comments and the way you said it implied I knew nothing. Things like my "build up"
I don't need an apology from Justin. I was just messing with him. I mostly hear that lame comment from Domestic guys saying imports take tons of money to make fast.
I'll leave it up to my buddy to do the shit talking about racing you in his car, seeing how it is his car. You do have the AWD advantage, but maybe you guys can race from a 2nd gear roll.
I think everyone does a little assuming into things and just needs to chill. In real life I'm sure we'd all get along just fine, but on the net things get taken out of context.
ranta18
Jul 12 2004, 11:23 AM
Oh, and I don't think my 12.8 is anything to really brag about. Its good for around here I guess, but what I had done wasn't anything special and is nothing compared to the guys on the coasts. My new setup will be something to be proud of though. If it ever gets finished.
xian 1g
Jul 12 2004, 12:57 PM
thanks vfaqs... i doubt this helps, but i'm still looking
What is a "hacked" MAS?
What is an "Al Blaha" MAS?
What is a "Mike Jackson" MAS?
A "hacked" MAS is a first-generation MAS sensor that has had a large amount of the lower opening cut away. The resulting sensor has a lower section that is much larger than the upper section. The air going through the lower section is not measured by the ECU, while the air through the upper section is. The net result is a sensor that flows more air than stock, but measures less air than stock.
The other terms are references to the people who offered the hacking modification as a service, back when it was not well understood. Al Blaha is the one widely credited with inventing the process; Mike Jackson also offered hacked MAS units.
The "Blaha" MAS also included a resistor in-line with the MAS temperature sensor. This modification was intended to fool the ECU into thinking the air was colder than it really was. This helps offset the fact that there is more air going in to the engine than the ECU is actually measuring. It also included a small door to help the hacked MAS measure air better at idle. The exact details of the modification process is beyond the scope of this FAQ.
awd4kicks
Jul 12 2004, 01:14 PM
Hopefully you are all done now...
From now on I will be taking the liberty to completely wipe out entire threads if the BS is too thick to sort through. I'm not into mamby-pamby thread locking. If we can't have good info we wont have any info.
So keep the questions and answeres clear, to the point and try not to throw in expletives that seem to piss others off.
To the point...
The Blaha works....period
There are a number of them floating around the area and you can probably pick one up cheap enough not to worry about trying to hack up your stock MAS. Basically the resistor makes your ECU think that the outside air temp is MUCH cooler than it truely is. Cool air justifies more air volume in the computers programing. So this little resistor mod justifies any extra air that you are sucking through the MAS with your boost upgrades. The Blaha form of hacking the entire lower section of the MAS, simply cuts down on air restrictions and raises the effective CFM for more performance potential.
The only drawback to the blaha is rough idling prior to warm-up in cool weather. Blaha installs a removable flapper door to cut down on air volume during idle for this reason. It acts similar to a choke and it does the job.
BTW- My best runs were with a Blaha, a 190LPH pump that should have been upgraded and a stock fuel system with no fuel management beyond that. I have never heard of anyones engine being destroyed because they were running a Blaha MAS. People have burned up their pistons by running them too lean while they are using the Blaha though. Only thing to watch out for is the hardware from the flapper door coming loose and getting injested by the turbo.
awd4kicks
Jul 12 2004, 01:28 PM
QUOTE (ranta18 @ Jul 12 2004, 07:20 PM)
I admit my original comment was a little out of line and I should have used the word assinine to describe it.
Thank you but you don't have to defend yourself around here SO MUCH. It wont make any good difference.
With that being said the rest of the info after my last post is gone...
all_wheel_envy
Jul 12 2004, 01:41 PM
thank you and spy ill be in touch if anyone has one they want to part with pm me thanks again
ranta18
Jul 12 2004, 02:49 PM
Understood
From now on I'll let people think what they want and just let my work do the talking.
awd4kicks
Jul 12 2004, 03:21 PM

Rock On!
natedogg
Jul 12 2004, 05:55 PM
QUOTE (awd4kicks @ Jul 12 2004, 01:14 PM)
Hopefully you are all done now...
From now on I will be taking the liberty to completely wipe out entire threads if the BS is too thick to sort through. I'm not into mamby-pamby thread locking. If we can't have good info we wont have any info.
So keep the questions and answeres clear, to the point and try not to throw in expletives that seem to piss others off.
To the point...
The Blaha works....period
There are a number of them floating around the area and you can probably pick one up cheap enough not to worry about trying to hack up your stock MAS. Basically the resistor makes your ECU think that the outside air temp is MUCH cooler than it truely is. Cool air justifies more air volume in the computers programing. So this little resistor mod justifies any extra air that you are sucking through the MAS with your boost upgrades. The Blaha form of hacking the entire lower section of the MAS, simply cuts down on air restrictions and raises the effective CFM for more performance potential.
The only drawback to the blaha is rough idling prior to warm-up in cool weather. Blaha installs a removable flapper door to cut down on air volume during idle for this reason. It acts similar to a choke and it does the job.
BTW- My best runs were with a Blaha, a 190LPH pump that should have been upgraded and a stock fuel system with no fuel management beyond that. I have never heard of anyones engine being destroyed because they were running a Blaha MAS. People have burned up their pistons by running them too lean while they are using the Blaha though. Only thing to watch out for is the hardware from the flapper door coming loose and getting injested by the turbo.
all_wheel_envy - See this post for reply to PM. Kicks is my suga'.

Btw for a small fee, I can make you a Blaha if you can't find one for sale.
akamiami
Jul 12 2004, 06:09 PM
I remember seeing a blaha flapper door on the infamous hughes 'fireball' gvr4 back before I could afford such expensive parts. I was amazed at the shittiness of its construction. Truly crappy. I wouldn't put the blaha flapper on my car even if they promised to buy me a new turbo when it buggered up the current one.
A 1.6K resister in line with the diode on the side of the mas is all blaha did to change the 'measured' temperature anyways.
You guys are all cracking me up. bark bark bark all day but no bites.
natedogg
Jul 12 2004, 07:57 PM
Yeah, I remember reading about someone whose turbo ate the flapper door. Not good. When I had the Blaha on my fwd back in the day I didn't even bother with the flapper. It ran great without it. There was a definite improvement in performance with the Blaha in though.
ranta18
Jul 12 2004, 09:28 PM
Spy - Hands on experience from you? Umm... I'm not into that kind of stuff. If you did mean DSM's, don't you mean you want me to go talk to Slo-Pony and get some knowledge from him? From what I've heard he's the one that does all your work. OH SNAP! Just bustin your chops bud. Someone made me say it.
Sorry guys, they made me. I'm done playing high school now.
ranta18
Jul 13 2004, 01:01 AM
Dammit Spy! You owe me a new pair of boxers because I pissed in mine I was laughing so hard at you.
Let me first say I totally agree that Slo-Pony does excellent work and I have heard nothing bad about their service.
I'm quite sure you can handle jerry-rigging your car by yourself (the blaha mod, etc), but you leave the other stuff up to the people that know what they are doing correct? However, you run your mouth on the internet like you actually have done the work yourself. You make it sound like you are soooo busy that you can't even work on your own car that you love so much. Sounds like you're just making up a bunch of excuses for the fact that you either don't know how to or just don't want to **** it all up by trying. Thank you for not bringing anything to me in the future. I wouldn't want to be the one to blame for you getting your hands on it and blowing something up. I like how you talk shit about me and my work, but I doubt you've actually seen any of it. Your ignorance shines once again.
And then you top off all your stupidity with the physical threats. I moved on from high school a long time ago. Maybe you should too. Grow up.
eclipgst
Jul 13 2004, 01:18 AM
Wow its funny that somehow my car got brought into all this. This shit makes me laugh, keep it up.
soccerdude61587
Jul 13 2004, 01:45 AM
If spy lets slo pny do some work he gets guarantees because they back their work. Spy also helps support them, and in return Marcus will let him use tools. Tools that make Spy's work easier and faster. In the automotive world we help eachother out with the stuff we got. Its impossible for anyone to know everything or be able to do everything. Some people do bodywork, some paint, and others engines. Dont get me wrong doing it yourself is cool but when you dont do it right and break something later it will turn around and bite you in the @$$. Everyone on here knows what im talking about... breaking nuts... losing nuts... pets eating gaskets... dropping parts on your hand.. also you save yourself a HUGE headache of having your car sitting on stands for extended periods of time by letting a professional do it. Thats just my $.02
ranta18
Jul 13 2004, 08:48 AM
Dude, you really need to get your stories straight. NOT ONE THING you just said is true.
1. I have not chewed up ANY bearings on my motor and have not had to replace the head once. My motor has run perfectly fine as my times and dyno's have shown.
2. I have NO idea who Jeff Meiners is and I have not done ANY work on his car.
Know that the **** you are talking about before you start spreading lies!
ranta18
Jul 13 2004, 08:50 AM
Where the **** do you come up with this stuff. Get back on the meds man. Fast.
ranta18
Jul 13 2004, 09:30 AM
Yeah, sure, keep up the lies. I have no clue who that guy is and if you want, you can post his number and I'll call him about it if this person does exist and seems to think I did work on his car. Where and when was this supposed transaction and work done?
Grow up. False accusations and lies isn't going to hide the fact that you're and idoit.
ranta18
Jul 13 2004, 09:32 AM
Hey Spy, remember Dick Gobbler, he said you still owe him $500 for the penis pump and big rubber fist he sold you. Remember that? He said he doesn't want to have to bring it to court and smear your name in it, but he will if you don't pay up.
ranta18
Jul 13 2004, 10:21 AM
What I thought. You're the definition of asinine.
Pack of what? Kias? LOL... J/K guys. I've got love for the DSM's. To each his own. Do what you want and face the consequences or benifets that follow.
eclipgst
Jul 13 2004, 12:51 PM
Man you guys went from bitchin to make up sex pretty fast. Who is pitchin and whos recievin?
natedogg
Jul 14 2004, 11:10 AM
From what I've seen over the past couple of years, Spy has actually become quite a capable mechanic. I have no doubt that if the need arose he could rebuild an engine. Its not rocket science. Just takes patience, logical thinking, and some anality, if that's even a word.
ranta18
Jul 14 2004, 11:51 AM
Logical thinking is the problem. Spy couldn't even put together a peanut butter and jelly sandwich if his life depended on it. J/K!
awd4kicks
Jul 14 2004, 12:04 PM
QUOTE (akamiami @ Jul 13 2004, 12:09 AM)
I remember seeing a blaha flapper door on the infamous hughes 'fireball' gvr4 back before I could afford such expensive parts. I was amazed at the shittiness of its construction. Truly crappy. I wouldn't put the blaha flapper on my car even if they promised to buy me a new turbo when it buggered up the current one.
Although I think this description falls in line with the assinine one, I agree. I removed my flapper in the summer, but without it in the fall and winter my car would not run properly until warmed up. That crude little flapper did exactly what it was supposed to. I also used lock tite on the nuts when replacing the flapper to help prevent missing turbo fins. It's really not that hard to take the extra time for some preventative maintenance.
In my opinion this Blaha mod falls squarely into the DSM philosophy of building up performance with ingenuity versus dollars. Plus I've seen a well respected car or two that this sort of craftsmanship would blend right into.
Remember it's not how you stand by your rolling money pit that counts. It's how fast you can make that bitch run before it flips you off and skips town with the money you have invested. So keep it clean, keep it cheap, make it productive and tune it to the Nth degree.
Just my .02
ranta18
Jul 14 2004, 01:25 PM
You've got way too much time on your hands.
natedogg
Jul 14 2004, 05:09 PM
Spy - This time a year ago you didn't even want to tackle a transmission removal and install. You've got that under your belt now. You have turbo and wiring harness, uninstalls, and installs under your belt. You've got tuning her down. You've got the hoist and the engine stand. An engine rebuild should be easy as pie.
I appreciate your modesty, but your DSM mechanical knowledge has grown by leaps and bounds in the last couple of years.
Btw, the $10 charge for these comments can be deposited in my paypal account.
xian 1g
Jul 14 2004, 06:24 PM
i can vouch for the turbo uninstall install in a morning to make it too an auto-x...
i don't think it's his modesty... i think it's spy's complex that will cause him to argue with anything... I should set him up against my younger sister.. I think it would be a pretty good match... j/k.
QUOTE
Btw, the $10 charge for these comments can be deposited in my paypal account.
damn that's cheap, i couldn't pay people enough to say that they wouldn't mind if i was alive.... is that a friends rate, or can i get you say to i look good for that price?
xian 1g
Jul 14 2004, 07:39 PM

please note carefully that i did as requested and kept my mouth shut.
QUOTE
i think it's spy's complex
i left it ambigous as the male goats had told me not to tell any one about that, or the rash...
that said,
take a puff of the 1/2 inch bitch.
hmm... spy, master welder... that could come of some good use...

good luck. and do it.
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please
click here.