I have too much dsm stuff sitting in my shop and am going to get rid of it all if i cant sell it.
Here is a pretty good list of all the stuff I am trying to get rid of:

1g Tan interior including:
-center console carpeted side panels
-both bottom door trims (eagle talon)
-most of the trunk trim panels
-door panels
-side panels for back seats
-front and back seats (in fair shape)
-center console
-whole dash
-a pillars
1ga flip-up style white hood
1g power seat belts, tracks and motors
1g radio trim
1g intake manifold
evo shift forks (upgrades for 1g awd manual tranny for 1/2 and 3/4 forks)
1g uicp to tb intake hoses (I have 2; 1 has hole for nitrous jet)
1g power steering pump and bracket
1g rear seat belts (tan)
1g rearview mirror
1g drivers side mirror
1g top timing cover
1g interior roof light
1g radiator with fans - used but not corroded
1g red Laser front bumper cover
1g a/c evaporator
1g hatch weatherstripping
1g hood prop
1g white drivers side fender
1g front bumper support/crash bar
1g alternator
1g a/c compressor
1g turbo dash panel (138k on odo.)
1g spedometer cable
1990 style cam angle sensor
1990 style isc motor
1g flip-up headlights with motors
1g complete hvac panel and controls
1g hatch lock
1g heater core
1g a/c evaporator
1g blower
1g stock cassette player with brackets
1992 3000gt vr4 stock AM/FM/Cassette player
1g used starter
1g exhaust manifold (light hairline cracks/weldable)
1g fuel rail
1g fuel pressure regulator
1g fwd manual transmission (grinds in second)
1g battery tray
1g crank pulley
1g a/c lines
1g stock pistons and rods
1g stock catalytic convertor
1g (1990 manual fwd) intake cam
2g 7 bolt stock flywheel
2g crank pulley
2g n/t intake pipe and airbox
2g turbo airbox
2g oil filter housing
2g mains
2g oilpan
2g oil snorkle
2g 2pc timing cover
2g water pipe
2g used water pump
2g used front case/ oil pump
used 3 inch gm maf

Make me an offer on anything. Post here, pm me, or e-mail me at redleader36@fbx.com
Pick ups are welcome, but I live in north central Iowa.

Shoot me a price for the following if you have them.
Non-ABS Proportioning Valve
Non-ABS front brake lines
Non-ABS Master Cylinder to proportioning valve lines
Clutch Master Cylinder to rubber hose line

These are the small metal lines on the firewall, need for my ABS delete.

These are for a 1G

I'm interested in the EVO shift forks. PM me with details.

Rubber filler neck tube? It comes from the metal one, does a 90* bend, and into the tank, for a 1G AWD? If you can get it off without ripping it like i did. Thanks

90gsx, the cars i have parted out were both fwd. If the filler tube is the same (which i dont think it is) ill pull it off the chassis i got sitting here. I am trying to sell that chassis with as many pieces left on it as possible. Same for you taxiwardance, if i end up tearing up this chassis and you can use fwd brake lines, ill rip them off the car (gently) for you. Ill let you know in a few days if im gonna part out this chassis or sell it as it is.

sounds good, LMK

btw, is anybody interested in a 1990 fwd rolling chassis?

FWD and AWD are different. Thanks anyway

you wouldnt happen to have a 95 RS transmission would you

The only trannys I have are a 1990 manual fwd that grinds in 2nd and an automatic from a 1994 dodge stealth r/t. I am sure the 1g tranny will not work on a 2g (didnt chrysler make the 420a trannies) but the auto from the stealth might work. Ive heard the dsm and 3000gt/stealth autos are the same. This one has a bad end clutch, but that is very cheap and easy to replace with a $70-80 kit.

how much for the 1g fwd tranny and is it for turbo or nonturbo? Need one asap so let me know!

50 for your 1st gen manifold

Ryan, have you not noticed how every thread you post in from the FS forum gets locked? Take a hint and PM the seller please. We use the exchange now.

Yes. Please take the hint. PM the thread starter rather than replying to the thread.