Welcome Guest ( Log In | Register )

> Help, clutch
cjk123
post Oct 9 2007, 11:22 AM
Post #1


Person of Wisdom
***

Group: Members
Posts: 151
Joined: 16-March 04
From: Jacksonville and Champaign IL
Member No.: 260



Alright well for some reason when I push the clutch in and try to shift into gear it grinds right away. If i push the clutch in and hold it for a second then go to shift it shifts just fine. Please help me out cuz this is my daily driver and I really cant afford to grind gears and ruin my tranny.

Do any of you know why it grinds unless I hold it down?
Could it be the slave cylinder itself going bad?
Could the master cylinder?


--------------------
Hopefully getting back into things w/ a 90 laser rs-t
Go to the top of the page
 
+Quote Post
 
Start new topic
Replies (1 - 15)
black92_tsi_awd
post Oct 9 2007, 12:02 PM
Post #2


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



Pull the boot back on the slave, if there's fluid replace it. Same deal on the master, there will be fluid on the firewall. I'd recommend replacing both if one is bad.


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
cjk123
post Oct 9 2007, 12:32 PM
Post #3


Person of Wisdom
***

Group: Members
Posts: 151
Joined: 16-March 04
From: Jacksonville and Champaign IL
Member No.: 260



Is it if there is any fluid at all period? The slave is bone dry, but when I checked out the master was a slight bit of fluid, like it wasnt dripped down onto the fire wall or anything but there was a little fluid that i got on my fingers if i pulled the boot back and felt where the boot was.


--------------------
Hopefully getting back into things w/ a 90 laser rs-t
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Oct 9 2007, 01:49 PM
Post #4


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



it's probably fine then.
You could try bleeding the system in case there's some air in it.

Is it grinding in all gears?

When I had I similiar problem, I replaced a leaking slave and master and then my clutch throw out bearing ended up failing.


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
cjk123
post Oct 9 2007, 02:10 PM
Post #5


Person of Wisdom
***

Group: Members
Posts: 151
Joined: 16-March 04
From: Jacksonville and Champaign IL
Member No.: 260



I actually took it out and drove it. It seems to only be first and second that are doing it. I dont know why it just started today all the sudden though, before i could shift fine into second now i have to wait on it. I also didnt get on it hard so I do not know if the other gears would do it if i got on it and shifted hard


--------------------
Hopefully getting back into things w/ a 90 laser rs-t
Go to the top of the page
 
+Quote Post
cjk123
post Oct 9 2007, 02:15 PM
Post #6


Person of Wisdom
***

Group: Members
Posts: 151
Joined: 16-March 04
From: Jacksonville and Champaign IL
Member No.: 260



Is there anyone who knows a lot more about these cars than me that is willing to let me meet them somewhere and help me trouble shoot. I wish travis and christian still had their shop so I could go there.


--------------------
Hopefully getting back into things w/ a 90 laser rs-t
Go to the top of the page
 
+Quote Post
cjk123
post Oct 9 2007, 02:32 PM
Post #7


Person of Wisdom
***

Group: Members
Posts: 151
Joined: 16-March 04
From: Jacksonville and Champaign IL
Member No.: 260



Sorry man, im desperate


--------------------
Hopefully getting back into things w/ a 90 laser rs-t
Go to the top of the page
 
+Quote Post
cjk123
post Oct 9 2007, 10:31 PM
Post #8


Person of Wisdom
***

Group: Members
Posts: 151
Joined: 16-March 04
From: Jacksonville and Champaign IL
Member No.: 260



Well I guess I'm going to replace the slave cylinder, master cylinder, get an extended rod for the slave cylinder and change my tranny fluid as i know it is syncromesh but not sure how old since I just bought the car. Then also get my solid cable end bushings in.

I have not done the master cylinder on one of these cars before. As far as I can tell from looking at it and please tell me if I am wrong because I dont want to go to rip it out and be wrong and then have to ask.

1. Drain the brake fluid & remove the line that goes into the slave cylinder
2. Screw the slave rod all the way, not sure if this is a good idea or not, just seems much easier than trying to remove that cotter pin and deal with all of that.
3. Unbolt it from the engine side and pull it right out? (are there any bolts on the inside I need to remove?)
4. Put the new one it, screw the rod back in, hook the line back up to the slave and fill it.
5. Bleed it, how do I bleed the master cylinder? Where do I hook up the hose to bleed it or do I?


--------------------
Hopefully getting back into things w/ a 90 laser rs-t
Go to the top of the page
 
+Quote Post
natedogg
post Oct 10 2007, 08:53 AM
Post #9


Zen Master DSM
********

Group: Moderators
Posts: 3,008
Joined: 10-January 01
From: in front of you
Member No.: 5



You bleed the master cylinder the same way you bleed the slave. You are essentially bleeding the entire clutch hydraulic system.
Go to the top of the page
 
+Quote Post
cjk123
post Oct 10 2007, 11:23 AM
Post #10


Person of Wisdom
***

Group: Members
Posts: 151
Joined: 16-March 04
From: Jacksonville and Champaign IL
Member No.: 260



Alright, I kind of thought that after I posted but I figured I could still be wrong with that. Also Do I just unbolt it from the engine side and pull it out after the rod is disconnected from the inside?


--------------------
Hopefully getting back into things w/ a 90 laser rs-t
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Oct 10 2007, 12:01 PM
Post #11


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



Yep, that's what I did.

Make sure you don't pump the master dry when bleeding, otherwise you have to start over.

I would just set the clevis that attaches to the clutch pedal close on the new master. You'll have to adjust it for the new slave/master anyway to get the clutch engaement pedal height right anyway.


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
cjk123
post Oct 10 2007, 07:04 PM
Post #12


Person of Wisdom
***

Group: Members
Posts: 151
Joined: 16-March 04
From: Jacksonville and Champaign IL
Member No.: 260



Alright sounds good, I already got the slave and master, sadly I did not have time to get them done today and wont the next two days so It looks like sat morning will be when I put them in. Hopefully the master is as easy and slave was when I did that in my old car. I'm also going to install and extended slave rod, I have heard many statements about how they do nothing at all, but what the hell why not do it while I'm at it. Hopefully after the master, slave, extended rod, new syncromesh and solid end bushings the car will go back to shifting at least as good as it did before whatever happened the other day. I'll let you guys know how all of this goes.


--------------------
Hopefully getting back into things w/ a 90 laser rs-t
Go to the top of the page
 
+Quote Post
cjk123
post Oct 18 2007, 10:31 PM
Post #13


Person of Wisdom
***

Group: Members
Posts: 151
Joined: 16-March 04
From: Jacksonville and Champaign IL
Member No.: 260



Alright everything has been done to my tranny and still really no help at all. Through trouble shooting I'm kind of thinking its a bent clutch fork.
So I can do most work myself on this car but the tranny is something I have no experience with.
Out of the three dsms I've owned I have never had a tranny problem, I know luck me.

But basically I'm wondering about how much this would cost to fix if I took it somewhere and if anyone had any suggestions on where to take it.

Also how hard of a process would it been to drop the tranny and fix myself if I don't have the money to take it some place.

How bad will it mess up the car if at all if I just hold the clutch in for a slight second before shifting to prevent any grinding or anything like that until I can possibly get a tre tranny after winter?

Thanks for all you help to this points and hopefully future help.


--------------------
Hopefully getting back into things w/ a 90 laser rs-t
Go to the top of the page
 
+Quote Post
black92_tsi_awd
post Oct 19 2007, 06:49 AM
Post #14


Eats and sleeps DSM jargin.
******

Group: Members
Posts: 1,995
Joined: 27-November 04
From: Yates City IL
Member No.: 389



Dropping the trans is not that hard. I've done it quite a few times and I'm probably doing it again this weekend. You need a large floor jack to set it on. I use a transmission jack that has a large platform on it. It's nice because I usally pull them by myself.

I've got it down to about 2.0 hours to remove it, so at a $65 shop rate you'd probably pay someone $260 tp remove and them replace it. So I would definitely try to pull it yourself to save some labor costs.

If it doesn't turn out to not be the fork or throwout bearing, you looking at taking it somewhere to get fixed.


--------------------
92 Eagle Talon TSI AWD "The Black Golfball" How fast can a 14B go???
91 Chevy C1500 "Problem Child" **SOLD**
01 Impala DD
07 Trailblazer Wife's new DD

Cars run on blood, sweat, and horsepower...
Without the first two, you can't get the last"

SOB Racing "Sitting On Blocks"
Go to the top of the page
 
+Quote Post
cjk123
post Oct 19 2007, 01:35 PM
Post #15


Person of Wisdom
***

Group: Members
Posts: 151
Joined: 16-March 04
From: Jacksonville and Champaign IL
Member No.: 260



Okay so today I drained the whole system again, put in the extended clutch slave rod and then refilled and rebled the system. It seems to be a little better now.
I dont think I could have bled the line any more either time. Both times I used 64oz of fluid.
The pedal is stiffer than it used to be before I did all this but that wasn't the problem I was trying to fix. I will let you all know what happens when I take her out and drive her probably Sunday Night.


--------------------
Hopefully getting back into things w/ a 90 laser rs-t
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: 17th November 2026 - 09:16 AM
Design by: IPB Download & eBusiness Discussions