 Bearings |
 Jul 7 2004, 01:17 PM
Post
#1
|
|
|
HONDA KILLER  Group: Members Posts: 14 Joined: 20-May 04 Member No.: 298  |
Do i have to press the bearings into the block? MY friend told me that the rear silent shaft bearing has to be pressed into the block! The reason i ask is because when i go my oil pan off, the silent shaft bearing was in the bottom. Thanks, matt
|
 |
 
|
 |
Replies
|
Jul 8 2004, 03:22 PM
Post
#2
|
|
 Post Master Group: Members Posts: 626 Joined: 25-September 02 From: Urbana, IL Member No.: 19 |
You can't just cut the old rear one and grind it smooth, you also have to fill the hole in it somehow, usually by tapping it and putting a bolt in it. You can just leave the front shaft in place and pull the belt if you want, but if the engine is out of the car you might as well pull it too. If you plan on leaving the front shaft in, there's not much reason to buy a kit unless you don't feel comfortable cutting and tapping the rear shaft.
I bought the kit mainly because I knew I'd probably destroy the front bearings trying to get them out to rotate them. Sure enough, the rear bearing of the front shaft fell into two pieces with just a light tap. The stock balance shaft bearings are really fragile. -------------------- Eric Wort
87 White Buick Turbo 'T' (11.71 @ 116.5, 1.61 60ft, slipping trans) 92 Teal Eagle Talon TSi AWD (burn victim) |
|
|
|
Posts in this topic
cheaf Bearings Jul 7 2004, 01:17 PM
natedogg If you are talking about a 4g63 then no, none of t... Jul 7 2004, 04:00 PM wortdog The factory manuals always refer to the balance sh... Jul 7 2004, 04:17 PM natedogg Ahh. Jul 7 2004, 04:33 PM cheaf Is it true that with that balance shaft removal ki... Jul 8 2004, 01:10 PM wortdog Not that I've ever heard of, and I've put ... Jul 8 2004, 01:16 PM cheaf Can you leave the front one in and remove the rear... Jul 8 2004, 01:35 PM ranta18 Make sure to block the oiling holes for the shafts... Jul 8 2004, 02:03 PM natedogg QUOTE (ranta18 @ Jul 8 2004, 02:03 PM)Make su... Jul 8 2004, 06:15 PM ranta18 LOL. I recently discovered Honda is one of the on... Jul 8 2004, 06:47 PM cheaf Ok, if i were to put te rear balance shaft bearing... Jul 9 2004, 05:43 PM wortdog Any work on the balance shafts is much much easier... Jul 10 2004, 01:40 AM wortdog QUOTE (ranta18 @ Jul 9 2004, 12:47 AM)Why can... Jul 10 2004, 01:43 AM ranta18 Ok, I looked that that link. That little stuby pi... Jul 10 2004, 12:32 PM wortdog Just ask Miami about how hard it is to pull the fr... Jul 10 2004, 03:34 PM resalturbo ooooooh weight, is it even going to be enough to m... Jul 10 2004, 03:44 PM ranta18 Why not just do it right and save the weight? Eve... Jul 11 2004, 11:33 AM wortdog On DSM's, one doesn't have to block the re... Jul 11 2004, 10:47 PM ranta18 AHHHHH....I see. I hadn't looked at it that c... Jul 12 2004, 07:48 AM natedogg QUOTE (wortdog @ Jul 11 2004, 10:47 PM)On DSM... Jul 12 2004, 05:15 PM ranta18 Why not? Why not just plug the oil hole in the en... Jul 12 2004, 05:56 PM natedogg Because if you don't cut it and plug it perfec... Jul 12 2004, 07:51 PM ranta18 LOL.... The two mods are of a completly different ... Jul 12 2004, 09:12 PM natedogg I hear ya and agree. I was just giving you a hard... Jul 14 2004, 05:21 AM awd4kicks Where did you find the eliminator for $20 Nat... Jul 14 2004, 07:49 AM natedogg Its been quite a while since I bought that, but I... Jul 14 2004, 04:31 PM
ranta18 My buddy ordered the $40 one and it should be... Jul 14 2004, 09:59 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 24th September 2026 - 08:20 AM |
Powered By IP.Board
© 2026 IPS, Inc.